Difference between revisions of "CRTC I2M"

From crtc.cs.odu.edu
Jump to: navigation, search
(9 intermediate revisions by the same user not shown)
Line 3: Line 3:
  
 
-----
 
-----
 
  
 
= Introduction =
 
= Introduction =
Line 13: Line 12:
 
# '''Tessellate3D (PODM 3D)''' (3D tessellation software)
 
# '''Tessellate3D (PODM 3D)''' (3D tessellation software)
 
# '''Tessellate2D (Triangle)''' (2D tessellation software)
 
# '''Tessellate2D (Triangle)''' (2D tessellation software)
# '''Convert Image''' (image format conversion software)
+
# '''Convert Image''' (image format conversion software)  
  
 
= Problem Domains =
 
= Problem Domains =
Line 33: Line 32:
  
 
* Input (left figure): Dimensions (255x255x229) with spacing (0.976562x0.976562x1.40002)
 
* Input (left figure): Dimensions (255x255x229) with spacing (0.976562x0.976562x1.40002)
* Uniform with Delta = default (middle figure): 205,416 tetrahedra
+
* Uniform with Delta = default (middle figure): 205,510 tetrahedra
* Uniform with Delta = 1.5 (right figure): 770,853 tetrahedra
+
* Uniform with Delta = 1.5 (right figure): 767,393 tetrahedra
  
 
Uniform with Delta = default (middle figure):
 
Uniform with Delta = default (middle figure):
Line 51: Line 50:
 
<code>-i, --input [filename]</code> (required)
 
<code>-i, --input [filename]</code> (required)
  
Input data. It could be an ASCII/Binary NRRD file, an image saved in .vtk format or any other format supported by the ITK library. For more information regarding the file formats supported by the ITK library, see [https://insightsoftwareconsortium.github.io/itk-js/docs/image_formats.html here].  
+
Input data. It could be an ASCII/Binary NRRD file, an image saved in .vtk format or any other format supported by the ITK library. For more information regarding the file formats supported by the ITK library, see [https://insightsoftwareconsortium.github.io/itk-js/docs/image_formats.html here].
  
 
<code>-o, --output [filename]</code> (optional)
 
<code>-o, --output [filename]</code> (optional)
Line 76: Line 75:
  
 
Enables the grading of the volume of the mesh. By default, the value of delta controls both the surface approximation and the size of the elements. Using this flag the value of delta will control only the surface approximation resulting in elements of higher volume inside the domain.
 
Enables the grading of the volume of the mesh. By default, the value of delta controls both the surface approximation and the size of the elements. Using this flag the value of delta will control only the surface approximation resulting in elements of higher volume inside the domain.
 +
 +
<code>--include-labels [unsigned char list]</code> (optional)
 +
 +
Labels that will be included in the mesh. If not specified, all labels will be included in the mesh. Cannot be used together with <code>--exclude-labels</code>.
 +
 +
<code>--exclude-labels [unsigned char list]</code> (optional)
 +
 +
Labels that will be excluded from the mesh. Keeps all labels in the mesh except the ones specified. If not specified, all labels will be included in the mesh. Cannot be used together with <code>--include-labels</code>.
  
 
=== Tessellate2D ===
 
=== Tessellate2D ===
 
The only type of input images that Tessellate2D supports is quadrilateral.
 
  
 
==== Examples ====
 
==== Examples ====
Line 98: Line 103:
  
 
<pre>docker run -v $(pwd):/data/ crtc_i2m tessellate2d --input ./Medical_Imaging_Data/2D/COVID-19-23354.tif --min-edge 15 --output ./COVID-19-23354,w=0.1,e=15.vtk</pre>
 
<pre>docker run -v $(pwd):/data/ crtc_i2m tessellate2d --input ./Medical_Imaging_Data/2D/COVID-19-23354.tif --min-edge 15 --output ./COVID-19-23354,w=0.1,e=15.vtk</pre>
 +
Meshes generated based on the image [https://phil.cdc.gov//PHIL_Images/23354/23354.tif 23354] retrieved from the [https://www.cdc.gov/media/subtopic/images.htm Centers for Disease Control and Prevention]. For the uniform mesh, the edge-size corresponds to 15 pixels. The adaptive was created by controlling the size of the elements based on the difference in the intensity of the pixels.
 +
 
More Detailed 2D examples of Medical Image Computing can be found [https://crtc.cs.odu.edu/Medical_Imaging_Example_Meshes#2D_Example_Meshes here].
 
More Detailed 2D examples of Medical Image Computing can be found [https://crtc.cs.odu.edu/Medical_Imaging_Example_Meshes#2D_Example_Meshes here].
  
Line 103: Line 110:
  
  
Note: For the description of the employed sizing function please see the software documentation section of [[#sizing-function-parameters|Tessellate3D]].
+
Note: For the description of the employed sizing function please see the software documentation section of [[#mesh-sizing-parameters|Tessellate3D]].  
  
 
<code>-i, --input [filename]</code> (required)
 
<code>-i, --input [filename]</code> (required)
Line 121: Line 128:
 
<code>-e,--min-edge [unsigned real]</code> (optional)
 
<code>-e,--min-edge [unsigned real]</code> (optional)
  
Sets the minimum element edge size of the generated elements that will be used by the sizing function. It is designed to be used in conjunction with <code>--weight-limit</code> controlling the size of the generated mesh. Using <code>--min-edge</code> &lt; ''1'' does not offer significant gain if the ''pixel size'' of the input image = ''1''.<br />
+
Sets the minimum element edge size of the generated elements that will be used by the sizing function. It is designed to be used in conjunction with <code>--weight-limit</code> controlling the size of the generated mesh. Using <code>--min-edge</code> &lt; ''1'' does not offer significant gain if the ''pixel size'' of the input image = ''1''.
 +
 
 +
''minimum-physical-size'' of input image = min(spacing * size).<br />
 
(Default: ''1 / 100'' * ''minimum-physical-size'')
 
(Default: ''1 / 100'' * ''minimum-physical-size'')
  
Line 178: Line 187:
 
''minimum-physical-size'' of input image = min(spacing * size).<br />
 
''minimum-physical-size'' of input image = min(spacing * size).<br />
 
(Default (if <code>--cnf-uniform</code> is specified): ''1 / 100'' * ''minimum-physical-size'').<br />
 
(Default (if <code>--cnf-uniform</code> is specified): ''1 / 100'' * ''minimum-physical-size'').<br />
(Default (if <code>--cnf-uniform</code> is specified): ''1 / 20'' * ''minimum-physical-size'').
+
(Default (if <code>--cnf-adaptive</code> is specified): ''1 / 20'' * ''minimum-physical-size'').
  
 
<code>--cnf-uniform</code> (optional)
 
<code>--cnf-uniform</code> (optional)
Line 186: Line 195:
 
<code>--cnf-adaptive</code> (optional)
 
<code>--cnf-adaptive</code> (optional)
  
Produces adaptive meshes for CNF data. The level of adaptivity is controlled by <code>--weight-limit</code> and <code>--min-edge</code> (see below). For more details about how sizing works see note at the end of the section.
+
Produces adaptive meshes for CNF data. The level of adaptivity is controlled by <code>--weight-limit</code> and <code>--min-edge</code> (see below). For more details about how sizing works see the [[#note-sizing-function|note]] at the end of the section.
  
 
<code>-w, --weight-limit [unsigned real]</code> (optional)
 
<code>-w, --weight-limit [unsigned real]</code> (optional)
Line 195: Line 204:
 
<code>-e, --min-edge [unsigned real]</code> (optional)
 
<code>-e, --min-edge [unsigned real]</code> (optional)
  
Sets the minimum element edge size of the generated elements that will be used by the sizing function. It is designed to give some control over the size of the generated mesh. Using <code>--min-edge</code> &lt; ''1'' does not offer significant gain if the ''voxel size'' of the input image = ''1''.  (Default: ''1 / 100'' * ''minimum-physical-size'').
+
Sets the minimum element edge size of the generated elements that will be used by the sizing function. It is designed to give some control over the size of the generated mesh. Using <code>--min-edge</code> &lt; ''1'' does not offer significant gain if the ''voxel size'' of the input image = ''1''.
 +
 
 +
''minimum-physical-size'' of input image = min(spacing * size).<br />
 +
(Default: ''1 / 100'' * ''minimum-physical-size'').
  
 
<code>-b, --background-value [signed real]</code> (optional)
 
<code>-b, --background-value [signed real]</code> (optional)
Line 202: Line 214:
 
(Default: +oo).
 
(Default: +oo).
  
Note: Sizing Function
+
===== Note: Sizing Function =====
 +
 
  
 
The input image is used as a background(BG) mesh while refining the mesh. Before the beginning of the refinement, the input image is analyzed, and the global constraints of ''maximum-element-edge-size'' and ''element-weight-range'' are computed. The refinement algorithm queries the sizing function (SF) to verify whether each element satisfies the global and user constraints. Each time SF is called upon an element, it will check if its size meets the global (''maximum-element-edge-size'') and user (''min-edge'') constraints. Consequently, it will create a set SP of sampling points out of the element. This set consists of the element’s vertices, barycenter, and midpoints of vertices and barycenter. The sampling points that are preserved out of SP are those that lie within the BG mesh. Using the BG mesh, a set V of the values of SP is created. Subsequently, the quantity max(V) - min(V) is evaluated. If abs(max(V) - min(V))/''element-weight-range'' exceeds the user constraint ''weight-limit'', the element is split.
 
The input image is used as a background(BG) mesh while refining the mesh. Before the beginning of the refinement, the input image is analyzed, and the global constraints of ''maximum-element-edge-size'' and ''element-weight-range'' are computed. The refinement algorithm queries the sizing function (SF) to verify whether each element satisfies the global and user constraints. Each time SF is called upon an element, it will check if its size meets the global (''maximum-element-edge-size'') and user (''min-edge'') constraints. Consequently, it will create a set SP of sampling points out of the element. This set consists of the element’s vertices, barycenter, and midpoints of vertices and barycenter. The sampling points that are preserved out of SP are those that lie within the BG mesh. Using the BG mesh, a set V of the values of SP is created. Subsequently, the quantity max(V) - min(V) is evaluated. If abs(max(V) - min(V))/''element-weight-range'' exceeds the user constraint ''weight-limit'', the element is split.
Line 230: Line 243:
  
  
Note: For the description of the employed sizing function please see the software documentation section of [[#sizing-function-parameters|Tessellate3D]].
+
Note: For the description of the employed sizing function please see the software documentation section of [[#mesh-sizing-parameters|Tessellate3D]].
  
 
<code>-i, --input [filename]</code> (required)
 
<code>-i, --input [filename]</code> (required)
Line 248: Line 261:
 
<code>-e,--min-edge [unsigned real]</code> (optional)
 
<code>-e,--min-edge [unsigned real]</code> (optional)
  
Sets the minimum element edge size of the generated elements that will be used by the sizing function. It is designed to be used in conjunction with <code>--weight-limit</code> controlling the size of the generated mesh. Using <code>--min-edge</code> &lt; ''1'' does not offer significant gain if the ''pixel size'' of the input image = ''1''.<br />
+
Sets the minimum element edge size of the generated elements that will be used by the sizing function. It is designed to be used in conjunction with <code>--weight-limit</code> controlling the size of the generated mesh. Using <code>--min-edge</code> &lt; ''1'' does not offer significant gain if the ''pixel size'' of the input image = ''1''.
 +
 
 +
''minimum-physical-size'' of input image = min(spacing * size).<br />
 
(Default: ''1 / 100'' * ''minimum-physical-size'')
 
(Default: ''1 / 100'' * ''minimum-physical-size'')
  
Line 318: Line 333:
 
Below is the detailed information about the parameters of <code>tessellate3d</code>:
 
Below is the detailed information about the parameters of <code>tessellate3d</code>:
  
=== Input / Output Parameters ===
+
=== I/O Parameters ===
  
 
<code>-i, --input [filename]</code> (required)
 
<code>-i, --input [filename]</code> (required)
Line 333: Line 348:
 
If given, the surface of the produced mesh will be saved into <code>filename</code> in the VTK format.
 
If given, the surface of the produced mesh will be saved into <code>filename</code> in the VTK format.
  
=== Hardware Parameters ===
+
<code>-r, --file-format {0,1}</code> (optional)
 +
 
 +
Sets file format of outputFiles. <code>0</code> for ASCII, and <code>1</code> for BINARY.<br />
 +
(Default: ASCII).
 +
 
 +
=== Performance Parameters ===
  
 
<code>-t, --threads [unsigned integer]</code> (optional)
 
<code>-t, --threads [unsigned integer]</code> (optional)
Line 345: Line 365:
 
(Default: 1).
 
(Default: 1).
  
<code>-m, --memory-limit [Unsinged integer in MB]</code> (optional)
+
<code>-m, --memory-limit [unsinged integer in MB]</code> (optional)
  
 
Constrains the amount of memory in MB that will be used.<br />
 
Constrains the amount of memory in MB that will be used.<br />
Line 360: Line 380:
 
(Default (if <code>--sizing-function</code> is specified): ''1 / 20'' * ''minimum-physical-size'').
 
(Default (if <code>--sizing-function</code> is specified): ''1 / 20'' * ''minimum-physical-size'').
  
Delta is an essential parameter that is involved in every step of the PODM algorithm and guarantees the quality and fidelity of the produced mesh. If using d_1 creates N_1 elements then d_1/2 will create (Approximately) 8 = 2^3 times more elements while 2*d_1 will generate 1/8N_1 elements. A table which shows the relation between delta and mesh size can be found in the [[#how-mesh-size-relates-to-delta|Appendix]]. For more information on how delta affects the density of the sampling, see [https://crtc.cs.odu.edu/pub/papers/journal_58.pdf Guaranteed Quality Tetrahedral Delaunay Meshing for Medical Images].
+
Delta is an essential parameter that is involved in every step of the PODM algorithm and guarantees the quality and fidelity of the produced mesh. If using ''d_1'' creates ''N_1'' elements then ''d_1/2'' will create (approximately) ''8'' = ''2^3'' times more elements while ''2'' * ''d_1'' will generate ''1/8N_1'' elements. A table which shows the relation between delta and mesh size can be found in the [[#how-mesh-size-relates-to-delta|Appendix]]. For more information on how delta affects the density of the sampling, see [https://crtc.cs.odu.edu/pub/papers/journal_58.pdf Guaranteed Quality Tetrahedral Delaunay Meshing for Medical Images].
  
 
<code>-g, --volume-grading</code> (optional)
 
<code>-g, --volume-grading</code> (optional)
Line 366: Line 386:
 
Enables the grading of the volume of the mesh. By default, the value of delta controls both the surface approximation and the size of the elements. Using this flag the value of delta will control only the surface approximation resulting in elements of higher volume inside the domain.
 
Enables the grading of the volume of the mesh. By default, the value of delta controls both the surface approximation and the size of the elements. Using this flag the value of delta will control only the surface approximation resulting in elements of higher volume inside the domain.
  
=== Pre-processing filters’ parameters ===
+
=== Pre-processing Parameters ===
  
 
<code>-s, --image-segmentation</code> (optional)
 
<code>-s, --image-segmentation</code> (optional)
Line 377: Line 397:
 
(Default: +oo).
 
(Default: +oo).
  
=== Sizing Function parameters ===
+
<code>--include-labels [unsigned char list]</code> (optional)
 +
 
 +
Labels that will be included in the mesh. If not specified, all labels will be included in the mesh. Cannot be used together with <code>--exclude-labels</code>.
 +
 
 +
<code>--exclude-labels [unsigned char list]</code> (optional)
 +
 
 +
Labels that will be excluded from the mesh. Keeps all labels in the mesh except the ones specified. If not specified, all labels will be included in the mesh. Cannot be used together with <code>--include-labels</code>.
 +
 
 +
=== Mesh Sizing Parameters ===
  
 
<code>-f, --sizing-function</code> (optional)
 
<code>-f, --sizing-function</code> (optional)
Line 395: Line 423:
 
<code>-e, --min-edge [unsigned real]</code> (optional)
 
<code>-e, --min-edge [unsigned real]</code> (optional)
  
Sets the minimum element edge size of the generated elements that will be used by the sizing function. It is designed to give some control over the size of the generated mesh. Using <code>--min-edge</code> &lt; ''1'' does not offer significant gain if the ''voxel size'' of the input image = ''1''.  (Default: ''1 / 100'' * ''minimum-physical-size'').
+
Sets the minimum element edge size of the generated elements that will be used by the sizing function. It is designed to give some control over the size of the generated mesh. Using <code>--min-edge</code> &lt; ''1'' does not offer significant gain if the ''voxel size'' of the input image = ''1''.
  
=== Post-processing filters’ parameters ===
+
''minimum-physical-size'' of input image = min(spacing * size).<br />
 +
(Default: ''1 / 100'' * ''minimum-physical-size'').
 +
 
 +
=== Post-processing Parameters ===
  
 
<code>-l, --linear-interpolation</code> (optional)
 
<code>-l, --linear-interpolation</code> (optional)
  
 
Performs Linear Interpolation over the points of the produced mesh using the input image. It should not be used for input images that are already segmented/labeled.
 
Performs Linear Interpolation over the points of the produced mesh using the input image. It should not be used for input images that are already segmented/labeled.
 
=== Special Parameters ===
 
 
<code>--cnf-uniform</code> (optional)
 
 
Activates the flags <code>--image-segmentation</code>, and <code>--linear-interpolation</code> which are required for producing uniform size meshes for CNF data. Size of elements is controlled by <code>--delta</code>.
 
 
<code>--cnf-adaptive</code> (optional)
 
 
Activates the flags <code>--image-segmentation</code>, <code>--volume-grading</code>, <code>--sizing-function</code>, and <code>--linear-interpolation</code> which are required for producing adaptive meshes for CNF data. The level of adaptivity is controlled by <code>--weight-limit</code> and <code>--min-edge</code>.
 
  
 
=== Statistics Parameters ===
 
=== Statistics Parameters ===
Line 426: Line 447:
  
 
Computes and prints all statistics (thread and mesh).
 
Computes and prints all statistics (thread and mesh).
 +
 +
=== Special Parameters ===
 +
 +
<code>--cnf-uniform</code> (optional)
 +
 +
Activates the flags <code>--image-segmentation</code>, and <code>--linear-interpolation</code> which are required for producing uniform size meshes for CNF data. Size of elements is controlled by <code>--delta</code>.
 +
 +
<code>--cnf-adaptive</code> (optional)
 +
 +
Activates the flags <code>--image-segmentation</code>, <code>--volume-grading</code>, <code>--sizing-function</code>, and <code>--linear-interpolation</code> which are required for producing adaptive meshes for CNF data. The level of adaptivity is controlled by <code>--weight-limit</code> and <code>--min-edge</code>.
  
 
=== Miscellaneous Parameters ===
 
=== Miscellaneous Parameters ===
Line 438: Line 469:
 
Tessellate2D is a modified version of the [https://www.cs.cmu.edu/~quake/triangle.html ''Triangle''] software for 2D tessellation.
 
Tessellate2D is a modified version of the [https://www.cs.cmu.edu/~quake/triangle.html ''Triangle''] software for 2D tessellation.
  
The only type of input images that Tessellate2D supports is quadrilateral.<br />
 
 
The output meshes are in the [https://vtk.org/wp-content/uploads/2015/04/file-formats.pdf VTK format] and can be visualized using the open-source software [https://www.paraview.org Paraview].
 
The output meshes are in the [https://vtk.org/wp-content/uploads/2015/04/file-formats.pdf VTK format] and can be visualized using the open-source software [https://www.paraview.org Paraview].
  
Note: For the description of the employed sizing function please see the software documentation section of [[#sizing-function-parameters|Tessellate3D]].
+
Note: For the description of the employed sizing function please see the software documentation section of [[#mesh-sizing-parameters|Tessellate3D]].
  
 
Below is the detailed information about the parameters of <code>tessellate2d</code>:
 
Below is the detailed information about the parameters of <code>tessellate2d</code>:
Line 453: Line 483:
 
The filename of the output mesh saved in VTK format.<br />
 
The filename of the output mesh saved in VTK format.<br />
 
(Default: <code>outputMesh.vtk</code>).
 
(Default: <code>outputMesh.vtk</code>).
 +
 +
<code>-r, --file-format {0,1}</code> (optional)
 +
 +
Sets file format of outputFiles. <code>0</code> for ASCII, and <code>1</code> for BINARY.<br />
 +
(Default: ASCII).
  
 
<code>-w,--weight-limit [unsigned real]</code> (optional)
 
<code>-w,--weight-limit [unsigned real]</code> (optional)
Line 461: Line 496:
 
<code>-e,--min-edge [unsigned real]</code> (optional)
 
<code>-e,--min-edge [unsigned real]</code> (optional)
  
Sets the minimum element edge size of the generated elements that will be used by the sizing function. It is designed to be used in conjunction with <code>--weight-limit</code> controlling the size of the generated mesh. Using <code>--min-edge</code> &lt; ''1'' does not offer significant gain if the ''pixel size'' of the input image = ''1''.<br />
+
Sets the minimum element edge size of the generated elements that will be used by the sizing function. It is designed to be used in conjunction with <code>--weight-limit</code> controlling the size of the generated mesh. Using <code>--min-edge</code> &lt; ''1'' does not offer significant gain if the ''pixel size'' of the input image = ''1''.
 +
 
 +
''minimum-physical-size'' of input image = min(spacing * size).<br />
 
(Default: ''1 / 100'' * ''minimum-physical-size'')
 
(Default: ''1 / 100'' * ''minimum-physical-size'')
  

Revision as of 22:48, 5 April 2020



Introduction

This document contains instructions for downloading and using the crtc_i2m software suite developed by the CRTC lab at Old Dominion University.

The suite contains three software components:

  1. Tessellate3D (PODM 3D) (3D tessellation software)
  2. Tessellate2D (Triangle) (2D tessellation software)
  3. Convert Image (image format conversion software)

Problem Domains

The image-to-mesh conversion software suite that the CRTC has developed can be used in many different problem domains such as Medical Image Computing and Computational Nuclear Femtography. Specific instructions on how to use the software are described below.

Medical Image Computing

Tessellate3D

In Medical Image Computing, Tessellate3D can be used to generate meshes from multi-tissue segmented images.

Examples

Input image and clipped generated meshes

Head-Neck.png

  • Input (left figure): Dimensions (255x255x229) with spacing (0.976562x0.976562x1.40002)
  • Uniform with Delta = default (middle figure): 205,510 tetrahedra
  • Uniform with Delta = 1.5 (right figure): 767,393 tetrahedra

Uniform with Delta = default (middle figure):

docker run -v $(pwd):/data/ crtc_i2m tessellate3d --input ./Medical_Imaging_Data/3D/Head-Neck.mha --output ./Head-Neck,d=2.49023.vtk

Uniform with Delta = 1.5 (right figure):

docker run -v $(pwd):/data/ crtc_i2m tessellate3d --input ./Medical_Imaging_Data/3D/Head-Neck.mha --delta 1.5 -output ./Head-Neck,d=1.5.vtk

More Detailed 3D examples of Medical Image Computing can be found here.

Parameters

In this domain, some of the parameters of Tessellate3D take on different meanings. For the full range and descriptions of parameters please see the software documentation section of Tessellate3D.

-i, --input [filename] (required)

Input data. It could be an ASCII/Binary NRRD file, an image saved in .vtk format or any other format supported by the ITK library. For more information regarding the file formats supported by the ITK library, see here.

-o, --output [filename] (optional)

The filename of the output mesh saved in VTK format. (Default: outputMesh.vtk).

-c, --plc [filename] (optional)

If given, the surface of the produced mesh will be saved into filename in the VTK format.

-t, --threads [unsigned integer] (optional)

Sets the number of threads to be utilized.
(Default: 1).

-d, --delta [unsigned real] (optional)

Controls the density of surface approximation. Smaller values will lead to denser approximation close to the surface (and often to a more accurate surface representation), but will also lead to greater mesh size. The same delta value is used for every tissue of interest. A smaller delta value should be used if at least one of the tissues of interest is not recovered after the Meshing Procedure.

The maximum suggested value for delta is 1 / 5 of the minimum-physical-size of the input image, where minimum-physical-size = min(spacing * size).
(Default: 1 / 100 * minimum-physical-size).

-g, --volume-grading (optional)

Enables the grading of the volume of the mesh. By default, the value of delta controls both the surface approximation and the size of the elements. Using this flag the value of delta will control only the surface approximation resulting in elements of higher volume inside the domain.

--include-labels [unsigned char list] (optional)

Labels that will be included in the mesh. If not specified, all labels will be included in the mesh. Cannot be used together with --exclude-labels.

--exclude-labels [unsigned char list] (optional)

Labels that will be excluded from the mesh. Keeps all labels in the mesh except the ones specified. If not specified, all labels will be included in the mesh. Cannot be used together with --include-labels.

Tessellate2D

Examples

Input image and generated meshes

COVID-19-23354.png

  • Input (left figure) : Dimensions (3,000x2,000) with spacing (1x1)
  • Uniform with Min-Edge = 15 (middle figure) : 82,981 triangles
  • Adaptive with Min-Edge = 15 (right figure) : 67,920 triangles

Uniform with Min-Edge = 15 (middle figure):

docker run -v $(pwd):/data/ crtc_i2m tessellate2d --input ./Medical_Imaging_Data/2D/COVID-19-23354.tif --uniform --min-edge 15 --output ./COVID-19-23354,uniform,e=15.vtk

Adaptive with Min-Edge = 15 (right figure):

docker run -v $(pwd):/data/ crtc_i2m tessellate2d --input ./Medical_Imaging_Data/2D/COVID-19-23354.tif --min-edge 15 --output ./COVID-19-23354,w=0.1,e=15.vtk

Meshes generated based on the image 23354 retrieved from the Centers for Disease Control and Prevention. For the uniform mesh, the edge-size corresponds to 15 pixels. The adaptive was created by controlling the size of the elements based on the difference in the intensity of the pixels.

More Detailed 2D examples of Medical Image Computing can be found here.

Parameters

Note: For the description of the employed sizing function please see the software documentation section of Tessellate3D.

-i, --input [filename] (required)

Input data. It could be an ASCII/Binary NRRD file, an image saved in .vtk format or any other format supported by the ITK library. For more information regarding the file formats supported by the ITK library, see here.

-o, --output [filename] (optional)

The filename of the output mesh saved in VTK format.
(Default: outputMesh.vtk).

-w,--weight-limit [unsigned real] (optional)

Sets the element weight limit for the generated elements that will be used by the sizing function. This parameter limits the difference among the weights within one element. It is designed to give some control of the discretization error with respect to the input data.
(Default: 0.1)

-e,--min-edge [unsigned real] (optional)

Sets the minimum element edge size of the generated elements that will be used by the sizing function. It is designed to be used in conjunction with --weight-limit controlling the size of the generated mesh. Using --min-edge < 1 does not offer significant gain if the pixel size of the input image = 1.

minimum-physical-size of input image = min(spacing * size).
(Default: 1 / 100 * minimum-physical-size)

-u,--uniform (optional)

Creates a uniform mesh instead of an adaptive one. Uses --min-edge value as a constant size constraint.

Computational Nuclear Femtography

A short presentation can be found here.

Tessellate3D

Examples

Input image and clipped generated meshes

NT 3D.png

  • Input (left figure): Dimensions (100x100x100) with spacing (1x1x1), Voxels = 1,000,000
  • Uniform (middle figure): 768,033 tetrahedra
  • Adaptive (right figure): 253,516 tetrahedra

Uniform (middle figure):

docker run -v $(pwd):/data/ crtc_i2m tessellate3d --input ./CNF_Data/3D/CFF_14052019/NT_140519.nrrd --cnf-uniform --output ./NT_140519,d=1,uniform.vtk

Adaptive (right figure):

docker run -v $(pwd):/data/ crtc_i2m tessellate3d --input ./CNF_Data/3D/CFF_14052019/NT_140519.nrrd --cnf-adaptive --weight-limit 0.07 --output ./NT_140519,d=5,wl=0.07,me=1.vtk

More Detailed 3D examples of Computational Nuclear Femtography can be found here.

Parameters

In this domain, some of the parameters of Tessellate3D take on different meanings. For the full range and descriptions of parameters please see the software documentation section of Tessellate3D.

-i, --input [filename] (required)

Input data. It could be an ASCII/Binary NRRD file, an image saved in .vtk format or any other format supported by the ITK library. For more information regarding the file formats supported by the ITK library, see here.

-o, --output [filename] (optional)

The filename of the output mesh saved in VTK format.
(Default: outputMesh.vtk).

-t, --threads [unsigned integer] (optional)

Sets the number of threads to be utilized.
(Default: 1).

-d, --delta [unsigned real] (optional)

Controls the size of the elements near the boundary. Smaller values will lead to finer detail close to the boundary (and often to a more accurate boundary representation) but will also lead to a greater mesh size.

minimum-physical-size of input image = min(spacing * size).
(Default (if --cnf-uniform is specified): 1 / 100 * minimum-physical-size).
(Default (if --cnf-adaptive is specified): 1 / 20 * minimum-physical-size).

--cnf-uniform (optional)

Produces uniform size meshes for CNF data. Size of elements is controlled by --delta.

--cnf-adaptive (optional)

Produces adaptive meshes for CNF data. The level of adaptivity is controlled by --weight-limit and --min-edge (see below). For more details about how sizing works see the note at the end of the section.

-w, --weight-limit [unsigned real] (optional)

Sets the element weight limit of the generated elements that will be used by the sizing function. This parameter limits the difference among the weights within one element. It is designed to give some control of the discretization error with respect to the input data.
(Default: 0.1).

-e, --min-edge [unsigned real] (optional)

Sets the minimum element edge size of the generated elements that will be used by the sizing function. It is designed to give some control over the size of the generated mesh. Using --min-edge < 1 does not offer significant gain if the voxel size of the input image = 1.

minimum-physical-size of input image = min(spacing * size).
(Default: 1 / 100 * minimum-physical-size).

-b, --background-value [signed real] (optional)

Sets the voxel value that will be treated as a background value during the image segmentation. If none is desired, enter a value that does not exist in the dataset. In practice, a background value is a value that is ignored by the tessellation procedure. Regions of the tessellation corresponding to the background value will have no elements.
(Default: +oo).

Note: Sizing Function

The input image is used as a background(BG) mesh while refining the mesh. Before the beginning of the refinement, the input image is analyzed, and the global constraints of maximum-element-edge-size and element-weight-range are computed. The refinement algorithm queries the sizing function (SF) to verify whether each element satisfies the global and user constraints. Each time SF is called upon an element, it will check if its size meets the global (maximum-element-edge-size) and user (min-edge) constraints. Consequently, it will create a set SP of sampling points out of the element. This set consists of the element’s vertices, barycenter, and midpoints of vertices and barycenter. The sampling points that are preserved out of SP are those that lie within the BG mesh. Using the BG mesh, a set V of the values of SP is created. Subsequently, the quantity max(V) - min(V) is evaluated. If abs(max(V) - min(V))/element-weight-range exceeds the user constraint weight-limit, the element is split.

Tessellate2D

Examples

Input image and generated meshes

NT 2D.png

  • Input (left figure) : Dimensions (100x100) with spacing (1x1), Pixels = 10,000
  • Uniform (middle figure) : 7,587 triangles
  • Adaptive (right figure) : 1,038 triangles

Uniform (middle figure):

docker run -v $(pwd):/data/ crtc_i2m tessellate2d  --input ./CNF_Data/2D/NT_140519_50_X.vtk  --output NT_140519_X50_me_2_uniform.vtk --min-edge=2 --uniform

Adaptive (right figure):

docker run -v $(pwd):/data/ crtc_i2m tessellate2d  --input ./CNF_Data/2D/NT_140519_50_X.vtk  --output NT_140519_X50_me_2_wl_1e-1.vtk --min-edge=2 --weight-limit=0.1

More Detailed 2D examples of Computational Nuclear Femtography can be found here.

Parameters

Note: For the description of the employed sizing function please see the software documentation section of Tessellate3D.

-i, --input [filename] (required)

Input data. It could be an ASCII/Binary NRRD file, an image saved in .vtk format or any other format supported by the ITK library. For more information regarding the file formats supported by the ITK library, see here.

-o, --output [filename] (optional)

The filename of the output mesh saved in VTK format.
(Default: outputMesh.vtk).

-w,--weight-limit [unsigned real] (optional)

Sets the element weight limit for the generated elements that will be used by the sizing function. This parameter limits the difference among the weights within one element. It is designed to give some control of the discretization error with respect to the input data.
(Default: 0.1)

-e,--min-edge [unsigned real] (optional)

Sets the minimum element edge size of the generated elements that will be used by the sizing function. It is designed to be used in conjunction with --weight-limit controlling the size of the generated mesh. Using --min-edge < 1 does not offer significant gain if the pixel size of the input image = 1.

minimum-physical-size of input image = min(spacing * size).
(Default: 1 / 100 * minimum-physical-size)

-u,--uniform (optional)

Creates a uniform mesh instead of an adaptive one. Uses --min-edge value as a constant size constraint.

Software Documentation

The CRTC’s image-to-mesh software suite has been packaged into a Docker image for easy distribution and portability across multiple platforms. All that is needed to use it is an OS supporting Docker.

Requirements

  • OS: Linux, Windows 10 Pro/Enterprise, MacOS Sierra 10.12+
  • Docker

Installing Docker

Official documentation :

Note for Running on Windows

Docker on Windows uses Hyper-V VMs to run Linux containers. By default, the spawned VMs use 2 vCPUs and 2 GB RAM.

If performance is a concern, it is recommended to edit the Docker settings via the GUI to increase the resource allocation for the VMs in order to allow the tessellation3D tool to use more threads.

Getting The Software

The docker image containing the crtc_i2m software suite is located here (restricted access).

Docker Container Instructions

  1. Load the Docker Image.

    First of all, the Docker image needs to be loaded. The following command must be used:

    docker load --input [DOCKER_IMAGE_TAR]

    Note: If the user is not in the docker group, prepending sudo to the above command is necessary.

  2. Running

    • On MacOS/Linux

      docker run -v $(pwd):/data/ crtc_i2m <application> [arguments]
    • On Windows with PowerShell (recommended)

      docker run -v ${PWD}:/data/ crtc_i2m <application> [arguments]

    Notice that in this case brackets {} are used instead of parenthesis ()

    • On Windows with the command line (cmd)

      docker run -v %cd%:/data/ crtc_i2m <application> [arguments]

Where <application> is one of the currently available tools : tessellate3d, tessellate2d, or convert_image.

Tessellate3D (PODM 3D)

The main component of the software suite is a 3D tessellation software called PODM3D, which is a parallel Image-to-Mesh conversion algorithm with quality and fidelity guarantees and is capable of generating unstructured tetrahedral meshes out of 3D structured data.

The output meshes are in the VTK format and can be visualized using the open-source software Paraview.

A quick way to view all available parameters and brief descriptions for them is to pass the -h, --help flag to tessellate3d.

Below is the detailed information about the parameters of tessellate3d:

I/O Parameters

-i, --input [filename] (required)

Input data. It could be an ASCII/Binary NRRD file, an image saved in .vtk format or any other format supported by the ITK library. For more information regarding the file formats supported by the ITK library, see here.

-o, --output [filename] (optional)

The filename of the output mesh saved in VTK format.
(Default: outputMesh.vtk).

-c, --plc [filename] (optional)

If given, the surface of the produced mesh will be saved into filename in the VTK format.

-r, --file-format {0,1} (optional)

Sets file format of outputFiles. 0 for ASCII, and 1 for BINARY.
(Default: ASCII).

Performance Parameters

-t, --threads [unsigned integer] (optional)

Sets the number of threads to be utilized. The upper bound of the number of threads that should be utilized is equal to the number of cores that you have. If the number of threads is greater than 1, the produced meshes may differ in terms of the number of elements up to 3% due to the nature of the employed parallelism technique.
(Default: 1).

-p, --thread-pinning {0, 1} (optional)

Controls the pinning of threads to cores. 0 doesn’t pin threads to cores (experimental), and 1 pins threads to cores.
(Default: 1).

-m, --memory-limit [unsinged integer in MB] (optional)

Constrains the amount of memory in MB that will be used.
(Default: 70% of the free memory).

Geometry Parameters

-d, --delta [unsigned real] (optional)

Controls the density of surface approximation. Smaller values will lead to denser approximation close to the surface (and often to a more accurate surface representation), but will also lead to greater mesh size. The same delta value is used for every tissue of interest. A smaller delta value should be used if at least one of the tissues of interest is not recovered after the Meshing Procedure. For uniform meshes (i.e. no --volume-grading), the total number of elements is related to delta through an inverse cubic law (approximately):

The maximum suggested value for delta is 1 / 5 of the minimum-physical-size of the input image, where minimum-physical-size = min(spacing * size).
(Default (if --sizing-function is not specified): 1 / 100 * minimum-physical-size).
(Default (if --sizing-function is specified): 1 / 20 * minimum-physical-size).

Delta is an essential parameter that is involved in every step of the PODM algorithm and guarantees the quality and fidelity of the produced mesh. If using d_1 creates N_1 elements then d_1/2 will create (approximately) 8 = 2^3 times more elements while 2 * d_1 will generate 1/8N_1 elements. A table which shows the relation between delta and mesh size can be found in the Appendix. For more information on how delta affects the density of the sampling, see Guaranteed Quality Tetrahedral Delaunay Meshing for Medical Images.

-g, --volume-grading (optional)

Enables the grading of the volume of the mesh. By default, the value of delta controls both the surface approximation and the size of the elements. Using this flag the value of delta will control only the surface approximation resulting in elements of higher volume inside the domain.

Pre-processing Parameters

-s, --image-segmentation (optional)

Performs Image Segmentation on non-segmented/unlabeled images using a given background value. It should not be used for input images that are already segmented/labeled. Uses --background-value as an optional parameter.

-b, --background-value [signed real] (optional)

Sets the voxel value that will be treated as a background value during the image segmentation. If none is desired, enter a value that does not exist in the dataset. In practice, a background value is a value that is ignored by the tessellation procedure. Regions of the tessellation corresponding to the background value will have no elements.
(Default: +oo).

--include-labels [unsigned char list] (optional)

Labels that will be included in the mesh. If not specified, all labels will be included in the mesh. Cannot be used together with --exclude-labels.

--exclude-labels [unsigned char list] (optional)

Labels that will be excluded from the mesh. Keeps all labels in the mesh except the ones specified. If not specified, all labels will be included in the mesh. Cannot be used together with --include-labels.

Mesh Sizing Parameters

-f, --sizing-function (optional)

Enables the sizing-function that is described below. Uses --weight-limit and --min-edge as optional parameters.
--sizing-function needs to be used in conjunction with --volume-grading so that the volume’s refinement will be mainly controlled by the sizing-function.

The input image is used as a background(BG) mesh while refining the mesh. Before the beginning of the refinement, the input image is analyzed, and the global constraints of maximum-element-edge-size and element-weight-range are computed. The refinement algorithm queries the sizing function (SF) to verify whether each element satisfies the global and user constraints. Each time SF is called upon an element, it will check if its size meets the global (maximum-element-edge-size) and user (min-edge) constraints. Consequently, it will create a set SP of sampling points out of the element. This set consists of the element’s vertices, barycenter, and midpoints of vertices and barycenter. The sampling points that are preserved out of SP are those that lie within the BG mesh. Using the BG mesh, a set V of the values of SP is created. Subsequently, the quantity max(V) - min(V) is evaluated. If abs(max(V) - min(V))/element-weight-range exceeds the user constraint weight-limit, the element is split.

The described sizing function was designed for the Computational Nuclear Femtography data. Nonetheless, another sizing function could be designed and employed if requested.

-w, --weight-limit [unsigned real] (optional)

Sets the element weight limit of the generated elements that will be used by the sizing function. This parameter limits the difference among the weights within one element. It is designed to give some control of the discretization error with respect to the input data.
(Default: 0.1).

-e, --min-edge [unsigned real] (optional)

Sets the minimum element edge size of the generated elements that will be used by the sizing function. It is designed to give some control over the size of the generated mesh. Using --min-edge < 1 does not offer significant gain if the voxel size of the input image = 1.

minimum-physical-size of input image = min(spacing * size).
(Default: 1 / 100 * minimum-physical-size).

Post-processing Parameters

-l, --linear-interpolation (optional)

Performs Linear Interpolation over the points of the produced mesh using the input image. It should not be used for input images that are already segmented/labeled.

Statistics Parameters

--thread-statistics (optional)

Computes and prints thread statistics.

--mesh-statistics (optional)

Computes and prints mesh statistics.

--all-statistics (optional)

Computes and prints all statistics (thread and mesh).

Special Parameters

--cnf-uniform (optional)

Activates the flags --image-segmentation, and --linear-interpolation which are required for producing uniform size meshes for CNF data. Size of elements is controlled by --delta.

--cnf-adaptive (optional)

Activates the flags --image-segmentation, --volume-grading, --sizing-function, and --linear-interpolation which are required for producing adaptive meshes for CNF data. The level of adaptivity is controlled by --weight-limit and --min-edge.

Miscellaneous Parameters

-v, --verbosity-level {0, 1, 2} (optional)

Controls the level of output text verbosity. 0 produces no output, 1 produces standard output, and 2 produces extensive output.
(Default: 1).

Tessellate2D (Triangle)

Tessellate2D is a modified version of the Triangle software for 2D tessellation.

The output meshes are in the VTK format and can be visualized using the open-source software Paraview.

Note: For the description of the employed sizing function please see the software documentation section of Tessellate3D.

Below is the detailed information about the parameters of tessellate2d:

-i, --input [filename] (required)

Input data. It could be an ASCII/Binary NRRD file, an image saved in .vtk format or any other format supported by the ITK library. For more information regarding the file formats supported by the ITK library, see here.

-o, --output [filename] (optional)

The filename of the output mesh saved in VTK format.
(Default: outputMesh.vtk).

-r, --file-format {0,1} (optional)

Sets file format of outputFiles. 0 for ASCII, and 1 for BINARY.
(Default: ASCII).

-w,--weight-limit [unsigned real] (optional)

Sets the element weight limit for the generated elements that will be used by the sizing function. This parameter limits the difference among the weights within one element. It is designed to give some control of the discretization error with respect to the input data.
(Default: 0.1)

-e,--min-edge [unsigned real] (optional)

Sets the minimum element edge size of the generated elements that will be used by the sizing function. It is designed to be used in conjunction with --weight-limit controlling the size of the generated mesh. Using --min-edge < 1 does not offer significant gain if the pixel size of the input image = 1.

minimum-physical-size of input image = min(spacing * size).
(Default: 1 / 100 * minimum-physical-size)

-u,--uniform (optional)

Creates a uniform mesh instead of an adaptive one. Uses --min-edge value as a constant size constraint.

-v,--verbose-level [0,1] (optional)

Controls the level of output text verbosity. 0 produces no output, and 1 produces standard output.
(Default: 1).

Convert Image

convert_image serves as a utility to convert input data between different types of image formats. It allows converting the input data between different image types supported by ITK enabling in some cases more post-processing filters in Paraview (e.g. contour plots). However, converting them using the following command enables all relevant image filters in Paraview.

docker run -v $(pwd):/data/ crtc_i2m convert_image input_image.nrrd output_image.vtk

Appendix

How mesh size relates to delta

Input Image: NT_140519.nrrd

  • The size of the input image is: (100x100x100)
  • Spacing of the input image: (1x1x1)
  • MinimumPhysicalSize = 100 * 1 = 100
  • Maximum suggested delta value is: 100 / 5 = 20
Delta # Vertices # Tetrahedra
20 147 430
10 563 1,780
5 2,686 10,210
2.5 13,366 56,274
1.25 79,086 401,610
0.625 520,538 2,922,427